Test and Measurement Forum

Update in serial decoding Window

Forum for discussing PicoScope version 6 (non-automotive version)

Update in serial decoding Window

Postby ulf_l » Mon Sep 18, 2017 9:49 am

Hello

There is a little issue with the updating of the serial decoding window:
If I set a filter condition, for example the frame-ID of a LIN-decoder the data are only displayed for a short time. It would be very helpful, if the frame is displayed so long, until the next frame with a fulfilled filter condition occures.
Actual it seems like the displayed frame will be cleared when the next frame arrived, no matter if it will fulfil the filter condition or not.

Kind regards,
Ulf
ulf_l
Newbie
 
Posts: 0
Joined: Sat Sep 02, 2017 5:51 am

Re: Update in serial decoding Window

Postby Martyn » Mon Sep 18, 2017 12:15 pm

Have you changed from "Current Buffer" to "All Buffers" in the table section ?
Martyn
Technical Support Manager
Martyn
Site Admin
Site Admin
 
Posts: 2787
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots

Re: Update in serial decoding Window

Postby ulf_l » Mon Sep 18, 2017 5:59 pm

Hello

I think I have used the "current buffer" setting, but I'm not sure. I will try it to morrow again.

Best regards,
Ulf
ulf_l
Newbie
 
Posts: 0
Joined: Sat Sep 02, 2017 5:51 am

Re: Update in serial decoding Window

Postby ulf_l » Tue Sep 19, 2017 4:08 pm

Hello

It doesn't matter if the setting is in current or all buffers. With all buffers it might take a little more time until all buffers run out of date. To track a Lin-Message with a specified ID it would be great if the message didn't disappear until the next message with a match to the filter condition will occur.

Kind regards,
Ulf
ulf_l
Newbie
 
Posts: 0
Joined: Sat Sep 02, 2017 5:51 am

Re: Update in serial decoding Window

Postby Martyn » Thu Sep 28, 2017 6:40 am

Do you mean that you wish to have the decoded data for buffers that are no longer in the waveform buffer memory ? In effect a continuous log of the data, but filtered ?
Martyn
Technical Support Manager
Martyn
Site Admin
Site Admin
 
Posts: 2787
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots

Re: Update in serial decoding Window

Postby ulf_l » Tue Oct 03, 2017 11:26 am

Hello Martyn

If you say
Do you mean that you wish to have the decoded data for buffers that are no longer in the waveform buffer memory
it sounds a little bit strange ... viewing data that are no longer present.
But yes,
In effect a continuous log of the data, but filtered
that would be very helpful to scan serial streams with filter conditions. For example if you know the problem comes with a specific frame, it would help very much to get the problem visualized.

Regards,
Ulf
ulf_l
Newbie
 
Posts: 0
Joined: Sat Sep 02, 2017 5:51 am

Re: Update in serial decoding Window

Postby Martyn » Thu Oct 05, 2017 10:57 am

The issue would be that, with no waveform in the buffer memory to correspond to a filtered packet, it would not be possible to look at the actual signal. I suggest emailing support@picotech.com to discuss this suggestion in more detail
Martyn
Technical Support Manager
Martyn
Site Admin
Site Admin
 
Posts: 2787
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots


Return to PicoScope 6 for Windows

Who is online

Users browsing this forum: No registered users and 0 guests