Do you have any resolution enhance active (more than 12 bits)? Are you using a custom probe setting of any kind? Can you post a data file so we can see your settings? _________________ Tom Roberts (The Picotologist) http://www.autonerdz.com skype: autonerdz THE PicoScope Automotive Authority In Nort...

If I understand correctly, this sounds like normal operation in streaming mode. When you have filtering enabled and you are in streaming mode (display draws from left to right), the filter is not applied until the capture is complete. This causes the display to appear unfiltered as it draws across t...

The startup settings are saved on the PC. The easiest way to transfer your startup settings to another PC is to save a psdata (or pssettings) file using your desired settings and then open this file using the other copy of PicoScope. Then simply save settings. Hope this helps... _________________ To...

Actually, you can achieve twice that sample rate on a 20ms capture and sample at 80MHz per channel and collect 1,600,000 samples on each one for a 12.5ns sample interval. :shock: The waveform buffer index will collect 7 of these screens. _________________ Tom Roberts (The Picotologist) http://www.au...

StrongT You are correct. The screens in the waveform buffer index are not seamless. Each screen is a seamless record but there are small gaps between the screens. These gaps will vary depending on what scope and what settings you are using. To minimize the impact of these gaps, you can increase the ...

If you don't already have the 4224, you would be better off getting the 4423 automotive kit, which has many automotive accessories. The kit is a much better value. Purchasing a scope and then only a few of the accessories included in the kit will actually cost more than the complete package. _______...

jmelton,

This bug has been corrected in the current release 6.2.2.12

_________________
Tom Roberts
(The Picotologist)
http://www.autonerdz.com
skype: autonerdz
THE PicoScope Automotive Authority
In North America

You are very welcome

_________________
Tom Roberts
(The Picotologist)
http://www.autonerdz.com
skype: autonerdz
THE PicoScope Automotive Authority
In North America

hillp, To open a data file without the converter attached so that the values are filled in, choose the appropriate demo device when prompted. Open PicoScope, say yes to demo device, choose the appropriate one. Then file/open your data file from within PicoScope. At this time, Pico 6 has a bug that w...

Here is a link to the Mixmaster manual: http://www.picotech.com/document/pdf/mixmaster.pdf Place the negative fired cylinders on one bank of the Mixmaster and the positively fired ones on the other bank. The position of the A/A+B switch depends on how you want to view the signals. The A position spl...

A 3424 or 3423 would sample at 333.3 KHz on each of four channels with a 5 second capture time.

10.42KHz with a 200 second capture time.

_________________
Tom Roberts
(The Picotologist)
http://www.autonerdz.com
skype: autonerdz
THE PicoScope Automotive Authority
In North America

Dudi, When I have seen this issue it usually because the drivers did not install properly. Plugging in the hardware before software was installed or just didn't take properly for some other reason. Just an idea.... Have you removed the device from device manager and tried to install it again? With t...

Robin, Sounds like that is what he is doing. xavier, You can measure the voltage drop across the resistor, but then you will have a voltage potential on the scope ground. If you have other channels deployed, then this will feed through to the other channel grounds. I suggest you use a current probe:...

Guest, The best way to accomplish this with the current PicoScope 6 build is to apply a measured amount of resolution enhance to the channel you wish to filter. Be careful with this so as not to filter out things that may be important. Watch for an even better method in the next build 8) There are a...

The Autonerdz recommendations are a bit higher assuming you will be using PicoScope 6 Automotive with this: We suggest 1GHz processor or faster. We have found 256MB RAM to be inadequate. We recommend 1GB for XP and 2GB for Vista minimum. USB 2.0 is required to utilize the PicoScope 6 high speed stre...