CartThe following accessories may be used with the PicoScope 4000 Series of high–resolution USB Oscilloscopes and most other modern oscilloscopes.
- 60 MHz passive oscilloscope probe
- Active differential oscilloscope probes
- Attenuators
- Feed–through terminator
- IEPE accelerometer and mounting magnet
- PicoScope protective rubber case#
- PicoScope carry case#
# Not suitable for use with the PicoScope 4262.
MI007: 60 MHz Oscilloscope Probe x1/x10
This high quality general purpose oscilloscope probe, has a 60 MHz bandwidth. A two position slide switch allows attenuation of either x1 or x10 to be selected.
| MI007 Oscilloscope Probe Specifications | ||
|---|---|---|
| x1 | x10 | |
| Attenuation | 1:1 | 10:1 |
| Bandwidth | DC to 15 MHz | DC to 60 MHz |
| Rise time: | 23.3 ns | 5.8 ns |
| Input resistance | 1 MΩ | 10 MΩ |
| Input capacitance | 46 pF plus oscilloscope | Approx 15 pF |
| Working voltage | 600 V DC incl Peak AC (derating with frequency) | |
| Cable length | 1.2 M (approx 3 ft 11 in) | |
| Lead time | In stock | |
| Price | £15·00 US$24·75* €18,15* | |
Active Differential Oscilloscope Probes
Our active differential probes let you use a conventional earthed oscilloscope to measure signals that are not referenced to ground, including mains voltages. They can also be used to measure and observe the waveforms of three–phase supplies or the gate and control signals of semiconductor circuits. They are ideal for investigating motor speed controls, uninterruptible power supplies, switch mode power supplies and process controllers.
| Model | Bandwidth | Attenuation | Differential voltage range | Common mode voltage range | Input impedance | Price |
|---|---|---|---|---|---|---|
| TA041 | 25 MHz | x10 / x100 | ±70 V / ±700 V | ±1400 V | 4 MΩ / 5.5 pF | In stock £195·00 US$321·75* €235,95* |
| TA057 | 25 MHz | x20 / x200 | ±140 V / ±1400 V | ±1400 V | 4 MΩ / 5.5 pF | In stock £220·00 US$363·00* €266,20* |
| TA058 | 50 MHz | x10 | ±70 V | ±700 V | 1.6 MΩ / 7 pF | Despatched within 3 weeks £245·00 US$404·25* €296,45* |
| TA044 | 70 MHz | x100 / x1000 | ±700 V / ±7000 V | ±7000 V | 10 MΩ / 10 pF | In stock £480·00 US$792·00* €580,80* |
| TA043 | 100 MHz | x10 / x100 | ±70 V / ±700 V | ±700 V | 4 MΩ / 7 pF | Low stock £450·00 US$742·50* €544,50* |
| TA042 | 100 MHz | x100 / x1000 | ±140 V / ±1400 V | ±1400 V | 4 MΩ / 7 pF | In stock £330·00 US$544·50* €399,30* |
| TA045 | 200 MHz | x10 | ±60 V | ±20 V | 500 kΩ / 7 pF | In stock £600·00 US$990·00* €726,00* |
BNC Attenuator Set
The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.
Please note: The TA050 attenuators must be used with a matched 50-ohm source and load. If you wish to attenuate a signal before feeding it into a high-impedance measuring instrument, you must add a 50 ohm feedthrough terminator such as the Pico Technology TA051 feedthrough terminator.
| TA050 Specifications | |
|---|---|
| Bandwidth | DC to 1 GHz |
| Attenuation | 3 dB, 6 dB, 10 dB, 20 dB |
| Maximum power dissipation | 1 W |
| Input impedance | 50 Ω |
| Output impedance | 50 Ω |
| VSWR | 1.5:1 or better |
| Dimensions | 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in) |
| Connectors | BNC, 1 male + 1 female |
| Construction | Shielded inner box with plastic shell |
| Weight | 24 g (approximately 0.85 oz) each |
| Lead time | In stock |
| Price | £39·00 US$64·35* €47,19* |
Feed-Through Terminator
The TA051 feedthrough attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50-ohm sources into instruments with high-impedance inputs, such as oscilloscopes.
| TA051 Specifications | |
|---|---|
| Bandwidth | DC to 1 GHz |
| Maximum power dissipation | 1 W |
| Input impedance | 50 Ω |
| Dimensions | 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in) |
| Connectors | BNC, 1 male + 1 female |
| Construction | Shielded inner box with plastic shell |
| Weight | 24 g (approximately 0.85 oz) each |
| Lead time | Low stock - order soon |
| Price | £9·50 US$15·67* €11,49* |
IEPE Accelerometer
| Performance | SI* |
|---|---|
| Sensitivity (±15%) | 10.2 mV/(m/s2) |
| Measurement range | ±490 m/s2 |
| Frequency range | 0.5 Hz to 10 kHz |
| Broadband resolution (1 Hz to 10 kHz) | 3434 µm/s2 |
| Non–linearity | ±1% |
| Transverse sensitivity | ≤ 7% |
| Electrical | SI* |
|---|---|
| Settling time (within 1% of bias) | ≤ 2.0 sec |
| Discharge time constat | ≥ 0.3 sec |
| Excitation voltage | 18 to 28 VDC |
| Constant Current Excitation | 2 to 20 mA |
| Output impedance | < 150 Ω |
| Output bias voltage | 8 to 12 VDC |
| Spectral noise (10 Hz) | 78.5 (µm/s2)√Hz |
| Spectral noise (100 Hz) | 49.1 (µm/s2)√Hz |
| Spectral noise (1 kHz) | 39.2 (µm/s2)√Hz |
| Electrical isolation (case) | > 108 Ω |
| Environmental | SI* |
|---|---|
| Overload limit (shock) | 49 050 m/s2 pk |
| Temperature range | -54 °C to + 121 °C |
| Enclosure rating | IP68 |
| Physical | SI* |
|---|---|
| Size (hex x height) | 14 mm x 64 mm |
| Weight (with cable) | 99.3 g |
| Mounting | stud |
| Mounting thread | 1/4-28 female |
| Mounting torque | 2.7 to 6.8 Nm |
| Sensing element | ceramic |
| Sensing geometry | shear |
| Housing material | stainless steel |
| Sealing | molded |
| Electrical connector | molded integral cable |
| Cable length | 3 m |
| Cable type | polyurethane |
* For English units and further technical detail,
please refer to the full manual (DO182)
The TA095 is a single–axis IEPE accelerometer that is suitable for use in a wide–range of applications.
Note: The TA095 can be used with any suitable device that provides a constant–current IEPE power source, such as the PicoScope 4224 IEPE.
In stock
Price £159·00
(approx US$262·35 / €192,39)
TA096 Mounting Magnet
The TA096 mounting magnet is used to securely mount the TA095 IEPE Accelerometer to ferrous materials.
Low stock - order soon
Price £30·00
(approx US$49·50 / €36,30)
PicoScope Protective Rubber Case
* Oscilloscope not included.
The PicoScope protective rubber case helps absorb potentially damaging physical shocks to your PicoScope whilst still giving you unobstructed access to all connectors.
A replaceable hanging bracket on the case also allows your PicoScope to be hung from a suitable hook — perfect for when you’re short on space.
Note: The PicoScope protective rubber case is not suitable for use with the PicoScope 4262.
In stock
Price £20·00
(approx US$33·00 / €24,20)
Spare / replacement hanging bracket for the PicoScope Protective Rubber Case
In stock
Price £2·00
(approx US$3·30 / €2,42)
PicoScope Carry Case
The PicoScope carry case can be used to protect your PicoScope Oscilloscope when used in the field, and to safely store it when it’s not needed.
The case uses foam to securely hold the PicoScope 2202, 3200 range and 4000# Series in place, preventing movement and providing cushioning to prevent damage. Space is also proved to store leads and scope probes.
Note: the PicoScope carry case is also supplied with our oscilloscope kits.
# Not suitable for use with the PicoScope 4262.
External dimensions: approximately 340 x 270 x 83 mm (13.4 x 10.6 x 3.3 in)
In stock
Price £30·00
(approx US$49·50 / €36,30)
* US Dollar and Euro prices are approximate. Your card will be billed in Pounds Sterling (GBP).
Share