3rd party parallel adapter cards

Post any questions about our parallel port products
Post Reply
PeterF
Advanced User
Advanced User
Posts: 435
Joined: Thu Jun 07, 2007 10:53 am
Location: Cambridgeshire

3rd party parallel adapter cards

Post by PeterF »

Hi,
Just to bring everything up to date, if you are running version R5.21.0 (or later) of PicoLog or PicoScope5, then most plug-in, PCI, PCI-Express & PCMCIA (Cardbus) parallel adapter cards will now work with our parallel port products. When using an adapter card with a laptop, the card has to be inserted in the laptop slot before boot in order to be recognised by our software.
If R5.21.0 is installed, then the ADC-212 scope can also be used running under PicoScope6 (automotive only) with an adapter card.
At present, it is still the situation that no USB to Parallel adapter will work with our parallel port devices. None of our parallel port devices will work at all, even with adapter, on 64 bit operating systems.
Regards,
PeterF.

Andy

Re: 3rd party parallel adapter cards

Post by Andy »

With a Startech Expresscard to Parallel interface and Picoscope 6 it's not possible to get an ADC-200 working with Windows 7 64-bit, right? :cry:

Andy

PeterF
Advanced User
Advanced User
Posts: 435
Joined: Thu Jun 07, 2007 10:53 am
Location: Cambridgeshire

Re: 3rd party parallel adapter cards

Post by PeterF »

Hi,
An ADC-200 will not work with PicoScope6 at all, nor with an 64 bit operating system. You will need PicoScope5, a 32 bit system and a 3rd party parallel adapter card.
Regards,
PeterF.

Nikki
Newbie
Posts: 0
Joined: Wed Aug 25, 2010 11:44 pm

Re: 3rd party parallel adapter cards

Post by Nikki »

I use a Sony Vaio Z11 running Windows 7 64 bits. So I decided to also add Windows 7 32 bits for a dual boot system solely to run ADC-212/50. The Startech Expresscard Parallel interface works nicely.

Can you tell me which USB oscilloscope is the ADC-212/50 equivalent?

ziko
Advanced User
Advanced User
Posts: 1705
Joined: Fri Dec 01, 2006 10:03 am
Location: St Neots

Re: 3rd party parallel adapter cards

Post by ziko »

Ziko

Technical Specialist

davidrossy
Newbie
Posts: 0
Joined: Wed Jan 04, 2012 8:33 pm

Re: 3rd party parallel adapter cards

Post by davidrossy »

I can't get my ADC200 to be recognised, With Express Card plugged in it appears in Device Manager as USB Printing Support (is that OK?) No change whether ADC200 plugged in or not and PIco Scope says ADC200 not connected.
I've tried re-starting with express card plugged in, with and without ADC200.

The ADC200 works fine on an old laptop with parallel port.

The express card is Chinese by ST Lab from Maplin compliant with Express card spec 1.0

Grateful for any help

David

Hitesh

Re: 3rd party parallel adapter cards

Post by Hitesh »

Hi David,

Unfortunately, a card which provides USB printing support only will not work. One way of checking this is that the correct type of adapter card requires a driver provided by the manufacturer whereas the wrong type does not and installs using a generic Windows driver.

We suggest the following for laptops with an Express card slot:-
http://www.delock.com/produkte/gruppen/ ... 66220.html

http://uk.startech.com/Cards-Adapters/P ... d~EC1PECPS

It might be worth contacting the manufacturer to confirm full parallel port support rather than just USB printing support.

I hope this helps.

rutherfordpaul
Newbie
Posts: 0
Joined: Wed Nov 14, 2012 7:54 am

Re: 3rd party parallel adapter cards

Post by rutherfordpaul »

If you "only" have a PCMCIA slot you may find the following exchange between StarTech and myself useful ..

Pico (the makers of Picoscope) recommend your EC1PECPS 1 Port ExpressCard Laptop Parallel Adapter Card - SPP/EPP/ECP as THE solution to interface with their parallel ported 'scopes.

Unfortunately my Dell laptop has a PCMCIA slot.

I could buy a Express to PCMCIA adapter as one possible solution to this interfacing problem but I am uncomfortable introducing an extra device which may make your express card disfunctional.

A possible alternative might be to use your CB1PECP 1 Port CardBus PCMCIA[/color] Parallel Laptop Adapter Card.

Which approach do you recommend (1) Express + adapter (2) PCMCIA without adapter?

... to which they replied ...

Thank you for your inquiry!

Our PCMCIA to Expresscard adapter will only work with USB based expresscards, which the EC1PECPS isn't (it's PCIe x1 based).

Therefore, your best option would be to go with the CB1PECP.

Concluding - I have decided not to take this approach (which saves the cost of the adapter) and additionally to sell the Dell + ADC ........ and put the money towards a new (USB!) Picoscope.

ziko
Advanced User
Advanced User
Posts: 1705
Joined: Fri Dec 01, 2006 10:03 am
Location: St Neots

Re: 3rd party parallel adapter cards

Post by ziko »

Thank you for your post we also have tested a PCMCIA one from Delock:

http://www.delock.de/produkte/F_360_Ser ... ale/1.html

Regards
Ziko

Technical Specialist

trezel
Newbie
Posts: 0
Joined: Wed Sep 24, 2014 8:35 am

Re: 3rd party parallel adapter cards

Post by trezel »

Hi,

Will picoscope 5 work with Lindy 51325 pci/parallel adapter card ?
(http://www.lindy.fr/Carte-PCI-1-port-pa ... 3&pi=51325)

For more info : Asus P5Q motherboard, win7 32bits

Hitesh

Re: 3rd party parallel adapter cards

Post by Hitesh »

Hi trezel,

I've answered a similar post from yourself on http://www.picotech.com/support/topic14457.html#p42445

Best wishes,

daveb
Newbie
Posts: 0
Joined: Thu Mar 30, 2017 4:45 am

Re: 3rd party parallel adapter cards

Post by daveb »

Is the situation with USB/parallel port adaptors still the same, i.e. no available adaptor will successfully operate a legacy parallel port device via USB? I have an ADC 216 that I can operate on a parallel port on a large older machine under XP but would like to eliminate that arrangement if possible. I can set up a smaller more modern machine running XP but it has no parallel port, just USB.
Dave B
Christchurch, NZ

Hitesh

Re: 3rd party parallel adapter cards

Post by Hitesh »

Hi Dave,

You can use a third party parallel port card as long as it is provided with drivers from the manufacturer and you have a 32-bit operating system.

Below are some recommendations for desktop PCs based on testing previously carried out (cards for laptops are covered in a previous post):

For desktops with PCI card slots:-
http://www.delock.com/produkte/gruppen/ ... 89015.html

For desktops with PCI Express card slots:-
http://www.delock.com/produkte/gruppen/ ... 89219.html

Hope this helps.

Post Reply