Test and Measurement Forum



Postby ziko » Fri Mar 02, 2007 2:24 pm

With Enviromon you can remotely log data to your PC via two GSM modems. In the set-up described below we have used the Wavecom Fastrack M1306B modems (however it should work on other modems)

http://www.linkwave.co.uk/products_sect ... /index.htm

Guidelines To Remote data logging:

1) Configure Your Enviromon system as though you have no modems, (please refer to your manual for this).

2) Ensure that once you have configured your device, you click on the "Program" button.

3) Exit and restart your software.

4) Once in the Configuration panel select "Equipment" (Settings->Configuration->Equipment)

5) Set the connection to "Via Telephone + Modem" with the serial cable still connected.
6) Choose the 9600 baud rate and click on Set Link and wait for it to complete. (You may need to click on "Set link" again if you get "Updating Time....Operation failed")

7) Clock on OK and exit the software then set the logger up at the remote site
8) Connect the power to the modem, (make sure modems running at 9600, you may need to do so via AT commands)
9) Disconnect the power and battery from the EL005
10) Connect the EL044* adapter and to the EL005, and connect the modem to the EL044.
11) Plug the power back in to the EL005. this will send an ‘automatically answer call’ signal to the modem.
12) Plug in the other modem into the PC in which you configured the Logger.
13) Go into the configuration panel and choose "Equipment".
14) Select ‘Telephone’. Enter the telephone number of the modem connected to the EL044/EL005.
15)If you require an alarm SMS message, fill in the details now. Choose ‘OK’.
16) Select which serial port the PC modem is attached to. Choose ‘OK’.
17)Select ‘Exit’.
18)Open the enviromon.ini file (located in your Enviromon or Pico Folder) and add the following at the end of the [General] Section:


19) Save and close the file, Restart EnviroMon.

20) From the ‘File’ menu select ‘connect’. Wait for the communication to take place, this may take up to 1 min. The program will display the current readings and then start downloading stored data. The readings will not change while the stored data is being downloaded.

21) Keep the program running until you hear the computer beep or until you see the current readings change again.

22) The telephone link stays active while the program is running or until you select ‘disconnect’ from the ‘File’ menu.

It is possible to set EnviroMon to automatically connect to the logger on start up and then disconnect after the data transfer. This can be done by selecting ‘disconnect after data transfer’ from the ‘connection at start up’ box in the telephone options dialogue.

Once the logger is connected via a telephone and modem link, it is possible to reprogram it if you need to update the settings. It is not possible to change the baud rate while connected via a modem.

If you do not know the baud rate of the modem used, try using 9600. This is supported by the vast majority of modems.

*EL044 replaces the EL033 as it is 9 way to 9 connector as opposed to the 9 -25Way EL033
Last edited by ziko on Wed Jan 21, 2009 1:48 pm, edited 4 times in total.

Technical Specialist
Advanced User
Advanced User
Posts: 1705
Joined: Fri Dec 01, 2006 10:03 am
Location: St Neots

GSM modems

Postby rpm » Mon Mar 05, 2007 1:46 pm


This is a comprehensive guide I have been working with siemens and Telit modem equipment after a battle at first. It pays to do work with hyper terminal to check simple things like the modem will auto answer ATS0=1. Can you advise the purpose of the code in section 18 of the report. I rarely try reprogramming as more than once I have found it fails and the logger is stopped necessitating an urgent vist
Posts: 5
Joined: Fri Sep 17, 2004 11:23 am
Location: Shropshire

Postby ziko » Tue Mar 06, 2007 11:14 am

Hi and thank you for the post.

The purpose of this, particularly the first line, in the enviromn.ini file is to extend the time at which the GSM modems communicate. Previously the default time was not sufficient and therefore there the Logger and computer were not completing communication.

Hope this helps.

Technical Specialist
Advanced User
Advanced User
Posts: 1705
Joined: Fri Dec 01, 2006 10:03 am
Location: St Neots

Postby chris t » Wed Jan 21, 2009 4:09 pm

When you talk about removing the power and battery on the EL005, does this refer to the internal battery and if so how is this removed?
chris t
Posts: 1
Joined: Wed Jan 21, 2009 4:03 pm

Postby gruntman » Thu Jan 22, 2009 12:12 am


To remove the internal battery simply remove the 4) screws under the rubber tabs on the back of the unit. Separate the two halves and you will see the rechargeable battery. Simply unplug the connector to disconnect the battery.


Richard Boyd
Crag Technologies, Inc
Advanced User
Advanced User
Posts: 109
Joined: Thu Sep 28, 2006 3:50 pm

Postby ziko » Thu Jan 22, 2009 9:50 am

Hi Chris,

Just to add to what Richard is saying, use if possible use a Pozidrive 1 screw driver and when you disconnect the battery only disconnect one lead so as not to get confused when you re-connect it.

Kind regards

Technical Specialist
Advanced User
Advanced User
Posts: 1705
Joined: Fri Dec 01, 2006 10:03 am
Location: St Neots

Return to Hardware

Who is online

Users browsing this forum: No registered users and 1 guest