Test and Measurement Forum

Connection between ADC-20 and Electronic Load

Post any questions you may have about our current range of USB data loggers

Connection between ADC-20 and Electronic Load

Postby want2know » Fri Sep 06, 2013 2:14 pm

Dear Sir/Madam,

I am doing Lithium ion cell discharge test, I want to use ADC 20 as well as terminal board for voltage, current and temperature measurement.

The battery is going to discharge through microprocessor controlled loads or programmable DC Electronic Load instead of using resistor. (I use this EL9000 http://www.elektroautomatik.de/en/produ ... l9000.html)

I have battery terminals connected directly to the positive and negative terminals of Electronic Load. But, I have no idea how can I connect the ADC 20 as well as terminal board to the Electronic Load to measure the discharge voltage and current.

Hope to hear you soon, thank you very much.
want2know
Newbie
 
Posts: 0
Joined: Tue Jul 30, 2013 2:54 pm

Re: Connection between ADC-20 and Electronic Load

Postby want2know » Tue Sep 10, 2013 7:52 am

Could someone please have a look?
want2know
Newbie
 
Posts: 0
Joined: Tue Jul 30, 2013 2:54 pm

Re: Connection between ADC-20 and Electronic Load

Postby Martyn » Tue Sep 10, 2013 8:41 am

Page 12 of the User Manual, http://www.picotech.com/document/brochures.html?id=44, will give you the pin outs of the connector with information on the differential pairs.
Martyn
Technical Specialist
Martyn
Site Admin
Site Admin
 
Posts: 2280
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots

Re: Connection between ADC-20 and Electronic Load

Postby want2know » Tue Sep 10, 2013 2:23 pm

Dear Sir,

This is a different question than the other thread but I got the same reply from you.

Dear Sir/Madam,

I am doing Lithium ion cell discharge test, I want to use ADC 20 as well as terminal board for voltage, current and temperature measurement.

The battery is going to discharge through microprocessor controlled loads or programmable DC Electronic Load instead of using resistor. (I use this EL9000 http://www.elektroautomatik.de/en/produ ... l9000.html)

I have battery terminals connected directly to the positive and negative terminals of Electronic Load. But, I have no idea how can I connect the ADC 20 as well as terminal board to the Electronic Load to measure the discharge voltage and current.

Hope to hear you soon, thank you very much.
want2know
Newbie
 
Posts: 0
Joined: Tue Jul 30, 2013 2:54 pm

Re: Connection between ADC-20 and Electronic Load

Postby Martyn » Wed Sep 11, 2013 6:56 am

Apologies for this

Doesn't the electronic load have the ability to provide this information ?

otherwise the information you were given in the other thread about measuring voltage and current is still applicable.
Martyn
Technical Specialist
Martyn
Site Admin
Site Admin
 
Posts: 2280
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots

Re: Connection between ADC-20 and Electronic Load

Postby want2know » Wed Sep 11, 2013 8:11 am

Dear Sir,

I would like to check with you if ADC-20 and terminal boards can be used along with any programmable electronic load? If yes, what are the? What I can see is from the device (please see attached file), there are only two terminals where I can connect to a DC source (in this case a battery), so I have no idea how could I connect ADC-20 to the programmable electronic load.

Thanks
Last edited by want2know on Wed Sep 11, 2013 12:21 pm, edited 1 time in total.
want2know
Newbie
 
Posts: 0
Joined: Tue Jul 30, 2013 2:54 pm

Re: Connection between ADC-20 and Electronic Load

Postby Martyn » Wed Sep 11, 2013 9:33 am

If you connect a battery, select battery test, then you shouldn't need the ADC-20 as the Electronic Load will provide you with the info you need.
Martyn
Technical Specialist
Martyn
Site Admin
Site Admin
 
Posts: 2280
Joined: Fri Jun 10, 2011 8:15 am
Location: St. Neots


Return to USB PC Data Loggers

Who is online

Users browsing this forum: No registered users and 0 guests