Search found 74 matches

by BSI
Tue Mar 27, 2012 6:45 pm
Forum: General Software Discussions
Topic: ETS in Rapid Block Mode
Replies: 2
Views: 2516

Re: ETS in Rapid Block Mode

Thx. Too bad.
Laurent
by BSI
Tue Mar 27, 2012 6:43 pm
Forum: General Software Discussions
Topic: Logical Triggering
Replies: 6
Views: 4514

Re: Logical Triggering

Thx Hitesh, I will look into it.
Regards,
Laurent
by BSI
Tue Mar 27, 2012 6:40 pm
Forum: USB PC Oscilloscopes
Topic: Cycling channels On and OFF over time
Replies: 4
Views: 3833

Re: Cycling channels On and OFF over time

I understand that, but I do not know the specs of the device in question with regards to turning on and off a channel. So this is the part I need your help for. Essentially what is the # cycles the ON OFF relay (if it is a relay) in the 4227 can take? There should be a spec for this.

Thx
Laurent
by BSI
Tue Mar 27, 2012 6:37 pm
Forum: LabVIEW
Topic: Logical Triggering Example
Replies: 5
Views: 3546

Re: Logical Triggering Example

Ok, thx Hitesh.
Laurent.
by BSI
Tue Mar 27, 2012 6:35 pm
Forum: USB PC Oscilloscopes
Topic: Conformal Coating
Replies: 5
Views: 3451

Re: Conformal Coating

Temperature range: -20/-10oC to + 40oC. I am mainly interested for the cold side of the range. Elevation: typically 2500m, but could be 5000m / 6000m. The board remains protected inside its case, and is sitting inside en enclosed enclosure Model: 4227. What would you recommend for conformal coating?...
by BSI
Tue Mar 20, 2012 6:15 pm
Forum: USB PC Oscilloscopes
Topic: Cycling channels On and OFF over time
Replies: 4
Views: 3833

Cycling channels On and OFF over time

I am using a Pico 4227 for an application that requires the device to be operating hours at a time. The general procedure being implemented is a Rapid Block Mode acquisition at 250MS/s (1 ch) or 125MS/s ( 2 ch) and filling up the buffer with a few thousands points at most, repeatedly ~ 500 times eve...
by BSI
Tue Mar 20, 2012 5:01 pm
Forum: General Software Discussions
Topic: ETS in Rapid Block Mode
Replies: 2
Views: 2516

ETS in Rapid Block Mode

Is there any plan to have ETS working for Rapid Block Mode ? At the moment it is supposed to only work with Rapid Block.
Thx
Laurent
by BSI
Tue Mar 20, 2012 3:28 am
Forum: LabVIEW
Topic: Logical Triggering Example
Replies: 5
Views: 3546

Logical Triggering Example

Hi, I attached an example based on the available lib from pico trying to use the Pico4000AdvancedTriggerSEttings.vi from the sdk ver r.10.1.0.17. My main objective is to get a logical trigger "A or B" working. To test the code, I use two 0-5 V square waves, one on channel A of a pico 4227, one on ch...
by BSI
Tue Mar 20, 2012 12:15 am
Forum: General Software Discussions
Topic: Logical Triggering
Replies: 6
Views: 4514

Re: Logical Triggering

Thx Hitesh.
I am using RapidBlock Mode, not streaming.

Yes, this is the same 4227 I was referring to with regards to conformal coating.
Laurent
by BSI
Sat Nov 26, 2011 1:52 am
Forum: USB PC Oscilloscopes
Topic: Conformal Coating
Replies: 5
Views: 3451

Re: Conformal Coating

Would you have any suggestion as which coating to use . Is there any concern with heat dissipation?
Thx
L.
by BSI
Thu Nov 24, 2011 6:44 pm
Forum: USB PC Oscilloscopes
Topic: Conformal Coating
Replies: 5
Views: 3451

Conformal Coating

Hi,
I was wondering if Pico digitizer boards could be ordered with conformal coating please?
Thx.
Laurent
by BSI
Thu Nov 24, 2011 6:38 pm
Forum: General Software Discussions
Topic: Logical Triggering
Replies: 6
Views: 4514

Re: Logical Triggering

Hi Hitesh, Can you clarify "the Number of the Sample" from your post please? Essentially I have 2 inputs connected to the digitizer. The signal comes alternatively from either A or B, and I want to make sure that when a trigger occurs from signal A (B) , it is actually the case so that I can pull th...
by BSI
Mon Nov 21, 2011 7:45 pm
Forum: General Software Discussions
Topic: Logical Triggering
Replies: 6
Views: 4514

Logical Triggering

With a 4227 set on logical triggering "Trigger on Input A or Input B" , does the driver return which input has received the trigger? I need to know which input was triggered to process my data accordingly. Processing will depend whether the signal was coming in from Input A or Input B.
Thx.
Laurent
by BSI
Mon Nov 21, 2011 7:40 pm
Forum: General Software Discussions
Topic: PicoScope 4000 series driver and XP embedded
Replies: 5
Views: 4423

Re: PicoScope 4000 series driver and XP embedded

Yes it works well. I now have tried and all is fine.
L.
by BSI
Wed Apr 13, 2011 6:11 pm
Forum: LabVIEW
Topic: Autotrigger in Rapid Block Mode
Replies: 4
Views: 3969

Autotrigger in Rapid Block Mode

Hi, I am working with a 4227, and LabVIEW performing Rapid Block Acquisition. I need to acquire a predefined number of captures, let's say 100, and average the resulting 100 segments. However, sometimes the incoming signal may change so that a trigger is not detected leading the digitizer to perform...