Search found 17 matches

by arielmedina
Tue Sep 27, 2005 2:24 pm
Forum: Pre-Sales Advice
Topic: ADC-16
Replies: 3
Views: 6958

OK, but any channel is acquired at the same time or is there a delay between a channel sample and the following? Thanks, Best Regards Ariel Hello, Thank you for your enquiry. The ADC16 will monitor all channels for you to perform calculations against using the PicoLog calculated parameters. Best reg...
by arielmedina
Tue Sep 27, 2005 2:10 pm
Forum:
Topic: ChA PicoScope 3205 is fixed at 20V
Replies: 1
Views: 5271

ChA PicoScope 3205 is fixed at 20V

I am using a PS3205 since April 05 and now the CHA is fixed at 20V. When I use the offset null tool, the screen shows a fixed line at zero.
Nevertheless, channel B is working OK.
Is there anything I can do or is this a hardware fault?

Thak you
Regards,

Ariel Medina
by arielmedina
Fri Jul 22, 2005 3:26 pm
Forum: PicoScope 5
Topic: Bode chart with PicoScope 3205
Replies: 4
Views: 7737

Thanks Sarah

Ariel
by arielmedina
Fri Jul 22, 2005 3:24 pm
Forum: PicoScope 5
Topic: Problems with picoscope SW
Replies: 7
Views: 10777

OK.

Thank you for your assistance.


Best Regards


Ariel
by arielmedina
Thu Jul 21, 2005 6:28 pm
Forum: PicoScope 5
Topic: Bode chart with PicoScope 3205
Replies: 4
Views: 7737

Hi, Sorry , my english too poor! I want to make a frequency response chart, this is a Graph of dB vs kHz of any sample like a filter. Looking into picotech web page, it says: "Built-in Signal Generator The PicoScope 3204 can output a fixed 1 kHz square wave for compensating oscilloscope probes. The ...
by arielmedina
Thu Jul 21, 2005 6:04 pm
Forum: PicoScope 5
Topic: Problems with picoscope SW
Replies: 7
Views: 10777

Hi, Thank you foryour post. No, It only happen with a number higher than about 700000. Ariel. Hi Thank you foryour post. I will need to pass this on to our software department for them to look into as I do not know myself why this might be happening. Does it only happen with this number of samples? ...
by arielmedina
Wed Jul 20, 2005 7:34 pm
Forum: PicoScope 5
Topic: Bode chart with PicoScope 3205
Replies: 4
Views: 7737

Bode chart with PicoScope 3205

One of its features is test the bandwith response of a filter using the sweep function with "peak hold " into signal genarator. I can´t get good results.
Could you advise how to do this?

Thak you


Ariel
by arielmedina
Wed Jul 20, 2005 12:11 pm
Forum: PicoScope 5
Topic: Problems with picoscope SW
Replies: 7
Views: 10777

Re: Problems with ps software

Hi, I was using the new version and I can see that it works very well. So, if I increase the maximun samples per scope trace, up to 800000 or 1x10 6, and then I use COPY AS TEXT function the PSW crash and gives this message: PSW32 provocó un error de página no válida en el módulo PSW32.EXE de 01...
by arielmedina
Wed Jun 22, 2005 11:38 am
Forum: PicoScope 5
Topic: Problems with picoscope SW
Replies: 7
Views: 10777

Problems with ps software

Thank you Sarah I´ll download this version and then I going to report you the results. Best regards, Ariel. Hi Thank you for your post. This was a software bug - we have since fixed this and if you use version 5.12.7 from our website then you should not see this problem again. Hope this helps Best ...
by arielmedina
Tue Jun 21, 2005 1:59 pm
Forum: PicoScope 5
Topic: Problems with picoscope SW
Replies: 7
Views: 10777

Problems with picoscope SW

Hi, I was using a 3205 with 5.11.8 version under both W98 and XP. When I open a ruler video problems starts to appear: The line trace of the ruler changes, the colours of channel are lost and turned to black, The tool bar of windows change to hiden aspect and in general the system is very unstable s...
by arielmedina
Tue Jun 07, 2005 1:38 pm
Forum: PicoScope 5
Topic: Position control on the screen
Replies: 6
Views: 9129

Hi Sarah,

Thak you very much for your technical assistance.

Best Regards

Ariel

CONIMED SA

Sarah wrote:Hi

Thank you for yourpost.

I will enter this suggestion into our customer feedback suggestions so that it can be passed on to our development team for consideration.

Best Regards
by arielmedina
Fri Jun 03, 2005 2:12 pm
Forum: PicoScope 5
Topic: Position control on the screen
Replies: 6
Views: 9129

Hi, Thank you for your message. Sorry, but if you choose any scope (analogue or digital), you can do this. You can move the figure while the scale is static. I know that the "absolute" readings will not be correct, but you can use the cursors to perform relative measures. On the other hand, I think ...
by arielmedina
Thu Jun 02, 2005 1:17 pm
Forum: PicoScope 5
Topic: Position control on the screen
Replies: 6
Views: 9129

Hi sarah Thank you for your reply. I know the x1 zoom tool for both axis, but when I move the figure , the scale of each axis move too. So I need move only the figure and keep the scale fixed. Best Regards Ariel Hi Ariel Thank you for your post. You should be able to do this by selecting the x1 zoom...
by arielmedina
Wed Jun 01, 2005 4:12 pm
Forum: PicoScope 5
Topic: Position control on the screen
Replies: 6
Views: 9129

Position control on the screen

I using PicoScope 5.11.8 with ADC212/50 in X-Y mode and I want to move the figure both up-down and right-left in the same mode like in a analogue scope using "position" knobs.
Is it possible?

Thanks

Ariel
by arielmedina
Tue May 31, 2005 2:11 pm
Forum: PicoScope 5
Topic: PicoScope under LabView 4.1
Replies: 1
Views: 4234

PicoScope under LabView 4.1

I am trying to link a PS3205 with labview 4.1 driver (ps 3000.vi)provided and it does not work.
Is possible that Labview 4.1 is a older version for it.

Thank you.

Ariel