Hi in the lab with different scopes and picoscope 6 i have been using the the CLI interface for remote controlling of the scope doing this in order to use the scope as a data logger with the recorded measurement data that i have been capturing with the csv argument "PicoScope.com /a Measurements.CSV...

Hi i use the Picoscope 6 software around the lab with PS5000 scopes and a picologger1216 i run picoscope6 continues with different measurements running i read out those measurements with the CLI interface "measurement.CSV" to my datalogging programs labview/python programs but i notes that with the ...

Hi Aaron I got both an 5000D and 5000A version And yes there is a issue with the detection of auxiliary Power for the 5000D but i am not sure if it also goes for the A/B versions as i just updated to newest SDK before i stepped on this issue at home, the A version is at work where i used it in a fue...

Hi I am using a 1216 to record data on more than 8 channels. In picoscope 6 the limit is 8 channels in one plot, and it creates a scope view more with additional channels to be viewed. When saving recordings it saves only the scope view that it selected before pushing the save button -> this is true...

You can get cheap China usb 2.0 isolators been using them to break ground loops but I don't remember how they work with picoscope but yes they are slow for streaming mode I have not seen any usb 3.0 isolators . But the way to go may be to use a ethernet/fiber/WiFi to usb 3.0 hub One could perhaps al...

hi I am using my 5000 series scope to do some logging of a PWM signal that vary in amplitude and duty cycle as well as the frequency from 30 Hz and down to 6 Hz the signal has to be sampled every 1 ms where i want to log the average, min and max value of the signal e.g over 10 sec this seems to work...

Hello to everyone, I'm preparing the measurement of stability of my SMPS prototype with my 5444D picoscope. The SMPS prototype is connected to my electronic load. The chracteristics of my SMPS prototype are: - input: 220 VAC (connected to the AC main) - output: 24VDC - 10A (240W) other informations...

Hello there
Will it be possible for me to request private message writing access ? so that i can write to other users and response to private message

Hello Aeron

Have you heard anything from Pico tech regarding the possible rounding issue in the scope driver ? when using the sigGen function instead of the awg function

Hey again Aaron
regarding the frequency shift error
did a test using the awg function and found that there is no shift over the 46.xxx KHz

cheers Martin

Hey Again Andrew Yes it is pure sine function ! Today i did a test using the AWG to set a specific frequency. I did the test in picoScope 6 and it looks like no rounding down above the ~46KHz so good :D ! So i did a deep measurement recording of the frequency and calculated the average frequency i d...

Hi Andrew thanks for the answer will check out.

please see the FRA4pico thread end about the issue
viewtopic.php?f=131&p=144942#p144942

Hi Aaron ! I do not have permission to write private messages and there is also some validation delay on my forum posts This is just guessing ! :) As the freq shift do not accrue at the same frequency makes me think this it is not a driver rounding issue But was wondering if the scope do the convers...

Hey i am having an issue with the setting the correct frequency on my scope generator i assume its some rounding issue. Scope: 5442B so what i do: PS5000AB_DDS_FREQUENCY 200e6 signalGeneratorPrecision = PS5000AB_DDS_FREQUENCY/2^32 // this also the lowest frequency that can be set double actualFreq =...

So today i did a test with the picoScope 6 software and DeepMeasurement + averaging the frequency column as i do not have an accurate frequency counter i entered the generator value 46566.128742 -> was rounded to 46.56613KHz and took the average value over 9310 cycles = 46566.13577 Hz then i entered...