Search found 109 matches
- Tue May 27, 2003 11:32 am
- Forum: Pre-Sales Advice
- Topic: 2-channel spectrum analyzer functions
- Replies: 2
- Views: 8156
Hello Scott, It sounds like you might be trying to measure the full frequency response of a system using a sweeping signal generator? If this is the case, then our current products won't be suitable. The built in signal generator is only for indication, and there is no facility to synchronize the un...
- Thu May 08, 2003 1:17 pm
- Forum: Getting Started
- Topic: ppm/dissolved solids probe
- Replies: 1
- Views: 4999
Hi Lance, PPM (parts per million) is a measure of ratio, hence you usually need to decide what chemicals you are measuring first. If you are just after a large particle count, then it's unlikely that DrDAQ will be suitable (none of our equipment have counters onboard). If you can find a sensor yours...
- Thu May 08, 2003 1:11 pm
- Forum: PicoScope 5
- Topic: automotive ignition
- Replies: 1
- Views: 4600
Hi John,
The Automotive kit is designed to be compatible with any standard ignition system with HT leads and the scope is more than fast enough. Check out the webpage for more details:
http://www.picotech.com/auto/
Best Regards,
The Automotive kit is designed to be compatible with any standard ignition system with HT leads and the scope is more than fast enough. Check out the webpage for more details:
http://www.picotech.com/auto/
Best Regards,
- Thu May 08, 2003 12:55 pm
- Forum: Getting Started
- Topic: connector issues
- Replies: 1
- Views: 4981
Hi Joel, The ADC-200 has two BNC inputs (same as any conventional osilloscope), you can use osilloscope probes, or find / make up your own leads ... its entirely up to your own preference. The ADC-200 uses a standard male to female all pins straight-through 25-way D connector cable. Hence the unit i...
- Thu May 08, 2003 12:24 pm
- Forum: General Software Discussions
- Topic: ADC1032.xls with USB Adapter
- Replies: 4
- Views: 9527
- Wed May 07, 2003 9:25 am
- Forum: General Software Discussions
- Topic: C experience, maybe helpful to others
- Replies: 1
- Views: 7001
- Wed May 07, 2003 8:18 am
- Forum: Pre-Sales Advice
- Topic: 433Mhz RF
- Replies: 5
- Views: 10403
Hi Tim,
You'll need to source a 433+ MHz scope from another supplier. If you type 'oscilloscopes' into a search engine, I'm sure you will find a suitable scope.
www.rswww.com will probably have something suitable.
Best Regards,
You'll need to source a 433+ MHz scope from another supplier. If you type 'oscilloscopes' into a search engine, I'm sure you will find a suitable scope.
www.rswww.com will probably have something suitable.
Best Regards,
- Fri May 02, 2003 1:12 pm
- Forum: General Software Discussions
- Topic: Single reads of ADC11 too slow in Labview
- Replies: 4
- Views: 8456
- Fri May 02, 2003 1:06 pm
- Forum: Pre-Sales Advice
- Topic: 433Mhz RF
- Replies: 5
- Views: 10403
- Fri May 02, 2003 8:11 am
- Forum: General Software Discussions
- Topic: Near Simultaneous Output and Reading
- Replies: 1
- Views: 6616
Hi, The digital out is a direct connection from a parallel port pin, therefore its response depends on your PC and windows. I wouldn't recommend using it for timing critical applications. Also ... because single processor PCs are ultimately single threaded in terms of execution order, you would stop...
- Thu May 01, 2003 12:55 pm
- Forum: General Software Discussions
- Topic: Controlling DrDaq using LabView Version 5
- Replies: 3
- Views: 7540
Hi, Labview 5 is no problem, the example files are downloadable (follow the download link at the bottom of the page). The Labview imports the driver routines from our standard dll files, already installed in your PICO installation directory. If you want to get the most out of Labview, you will need ...
- Thu May 01, 2003 12:13 pm
- Forum: General Software Discussions
- Topic: Console program link error
- Replies: 4
- Views: 11416
Hi again, I'm afraid I'm not an expert on compiler warnings, you're probably better off talking to Microsoft. One of the customers on the forum may know the answer ... but you are far more likely to get a response on a specific C++ forum (there's plenty around). The only thing I can suggest is to ru...
- Wed Apr 30, 2003 9:37 am
- Forum: General Software Discussions
- Topic: Console program link error
- Replies: 4
- Views: 11416
Hi, I'm afraid I've not encountered this error before, perhaps someone else on the forum will have seen it? Have you looked up the error on the MSDN ? I often find that this helps. http://msdn.microsoft.com/library/default.asp?url=/library/en-us/vccore98/html/lnk1106.asp I used the 'LNK1106' text to...
- Wed Apr 30, 2003 8:07 am
- Forum:
- Topic: ADC-216 accuracy specs
- Replies: 1
- Views: 5018
Hi Jeff, I assume you meant the ADC-16 here, as the ADC-216 does not measure differential signals (it has two single ended, common ground channels). In the ADC-16, the voltages are combined on the analogue side of the ADConverter, therefore the accuracy in differential mode is the same as the accura...
- Fri Apr 25, 2003 8:42 am
- Forum:
- Topic: Using pico scope in a high EMI environment
- Replies: 1
- Views: 5403
Hi Clive, I just wanted to check that if you are using an ADC without isolation, you aren't using it for voltages above 42V dc (for safety reasons)? The units are tested to standard EMC regulations so they will perform well under normal conditions. However ... they are not screened, so if you have p...