The following accessories may be used with the PicoScope 5200 range of oscilloscopes.

MI145: 250 MHz  Oscilloscope Probe x1/x10

oscilloscope probe

This high–quality general purpose oscilloscope probe, has a 250 MHz  bandwidth and has been compensated for use with the PicoScope 5000 Series. A two position slide switch allows attenuation of either x1 or x10 to be selected.

Model Bandwidth Attenuation Input resistance Input capacitance Maximum working voltage Price
MI145 250 MHz x1 / x10 x1: 1 MΩ
x10: 10 MΩ		 x1: 46 pF plus scope
x10: ≈11 pF		 600 V DC incl AC pk In stock
£25·00  
US$41·25*
€30,25*
 

Active Differential Oscilloscope Probes

Our active differential probes let you use a conventional earthed oscilloscope to measure signals that are not referenced to ground, including mains voltages. They can also be used to measure and observe the waveforms of three-phase supplies or the gate and control signals of semiconductor circuits. They are ideal for investigating motor speed controls, uninterruptible power supplies, switch mode power supplies and process controllers.

Model Bandwidth Attenuation Differential voltage range Common mode voltage range Input impedance Price
TA041 25 MHz x10 / x100 ±70 V / ±700 V ±1400 V 4 MΩ / 5.5 pF In stock
£195·00  
US$321·75*
€235,95*
 
TA057 25 MHz x20 / x200 ±140 V / ±1400 V ±1400 V 4 MΩ / 5.5 pF In stock
£220·00  
US$363·00*
€266,20*
 
TA058 50 MHz x10 ±70 V ±700 V 1.6 MΩ / 7 pF Despatched within 3 weeks
£245·00  
US$404·25*
€296,45*
 
TA044 70 MHz x100 / x1000 ±700 V / ±7000 V ±7000 V 10 MΩ / 10 pF In stock
£480·00  
US$792·00*
€580,80*
 
TA043 100 MHz x10 / x100 ±70 V / ±700 V ±700 V 4 MΩ / 7 pF Low stock
£450·00  
US$742·50*
€544,50*
 
TA042 100 MHz x100 / x1000 ±140 V / ±1400 V ±1400 V 4 MΩ / 7 pF In stock
£330·00  
US$544·50*
€399,30*
 
TA045 200 MHz x10 ±60 V ±20 V 500 kΩ / 7 pF In stock
£600·00  
US$990·00*
€726,00*
 

BNC Attenuator Set

TA050

The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.

Please note: The TA050 attenuators must be used with a matched 50-ohm source and load. If you wish to attenuate a signal before feeding it into a high-impedance measuring instrument, you must add a 50 ohm feedthrough terminator such as the Pico Technology TA051 feedthrough terminator.

TA050 Specifications
Bandwidth DC to 1 GHz
Attenuation 3 dB, 6 dB, 10 dB, 20 dB
Maximum power dissipation 1 W
Input impedance 50 Ω
Output impedance 50 Ω
VSWR 1.5:1 or better
Dimensions 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in)
Connectors BNC, 1 male + 1 female
Construction Shielded inner box with plastic shell
Weight 24 g (approximately 0.85 oz) each
Lead time In stock
Price £39·00  
US$64·35*
€47,19*

Feed-Through Terminator

TA051

The TA051 feedthrough attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50-ohm sources into instruments with high-impedance inputs, such as oscilloscopes.

TA051 Specifications
Bandwidth DC to 1 GHz
Maximum power dissipation 1 W
Input impedance 50 Ω
Dimensions 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in)
Connectors BNC, 1 male + 1 female
Construction Shielded inner box with plastic shell
Weight 24 g (approximately 0.85 oz) each
Lead time Low stock - order soon
Price £9·50  
US$15·67*
€11,49*

* US Dollar and Euro prices are approximate. Your card will be billed in Pounds Sterling (GBP).