CartThe following accessories may be used with the PicoScope 2200 range of oscilloscopes and most other modern oscilloscopes.
- 60 MHz passive oscilloscope probe
- 150 MHz passive oscilloscope probe
- 250 MHz passive oscilloscope probe
- Active differential oscilloscope probes
- Attenuators
- Feed-through terminator
- PicoScope carry case
MI007: 60 MHz Oscilloscope Probe x1/x10
This high quality general purpose oscilloscope probe, has a 60 MHz bandwidth. A two position slide switch allows attenuation of either x1 or x10 to be selected.
| MI007 Oscilloscope Probe Specifications | ||
|---|---|---|
| x1 | x10 | |
| Attenuation | 1:1 | 10:1 |
| Bandwidth | DC to 15 MHz | DC to 60 MHz |
| Rise time: | 23.3 ns | 5.8 ns |
| Input resistance | 1 MΩ | 10 MΩ |
| Input capacitance | 46 pF plus oscilloscope | Approx 15 pF |
| Working voltage | 600 V DC incl Peak AC (derating with frequency) | |
| Cable length | 1.2 m (approx 3 ft 11 in) | |
| Lead time | In stock | |
| Price | £15·00 US$24·75* €18,15* £15·00 US$24·75* €18,15* | |
Buy 2 x MI007 oscilloscope probes and get a FREE protective case
Buy a set of two 60 MHz oscilloscope probes and you can carry and store your probes in style with a free protective case.
In stock
Price £30·00
(approx US$49·50 / €36,30)
TA132: 150 MHz Oscilloscope Probe x1/x10
This passive high–impedance scope probe has a 150 MHz bandwidth and high–frequency trimming. A two position slide switch allows attenuation of either x1 or x10 to be selected.
| TA132 Oscilloscope Probe Specifications | ||
|---|---|---|
| X1 | X10 | |
| Attenuation | 1:1 | 10:1 |
| Bandwidth | DC to 10 MHz | DC to 150 MHz |
| Rise time: | 35 ns | 2.33 ns |
| Input Resistance | 1 MΩ | 10 MΩ |
| Input Capacitance | 15 pF | |
| Working Voltage | 600 V DC incl Peak AC CAT II | |
| Cable Length | 1.2 m (approx 3 ft 11 in) | |
| Lead time | In stock | |
| Price | £20·00 US$33·00* €24,20* | |
Buy 2 x TA132 oscilloscope probes and get a FREE protective case
Buy a set of two 150 MHz oscilloscope probes and you can carry and store your probes in style with a free protective case.
In stock
Price £40·00
(approx US$66·00 / €48,40)
TA131: 250 MHz Oscilloscope Probe x1/x10
This passive high–impedance scope probe has a 250 MHz bandwidth and high–frequency trimming. A two position slide switch allows attenuation of either x1 or x10 to be selected.
| TA131 Oscilloscope Probe Specifications | ||
|---|---|---|
| X1 | X10 | |
| Attenuation | 1:1 | 10:1 |
| Bandwidth | DC to 10 MHz | DC to 250 MHz |
| Rise time: | 35 ns | 1.4 ns |
| Input Resistance | 1 MΩ | 10 MΩ |
| Input Capacitance | 11 pF | |
| Working Voltage | 600 V DC incl Peak AC CAT II | |
| Cable Length | 1.2 m (approx 3 ft 11 in) | |
| Lead time | In stock | |
| Price | £25·00 US$41·25* €30,25* | |
Buy 2 x TA131 oscilloscope probes and get a FREE protective case
Buy a set of two 250 MHz oscilloscope probes and you can carry and store your probes in style with a free protective case.
In stock
Price £50·00
(approx US$82·50 / €60,50)
Active Differential Oscilloscope Probes
Our active differential probes let you use a conventional earthed oscilloscope to measure signals that are not referenced to ground, including mains voltages. They can also be used to measure and observe the waveforms of three–phase supplies or the gate and control signals of semiconductor circuits. They are ideal for investigating motor speed controls, uninterruptible power supplies, switch mode power supplies and process controllers.
| Model | Bandwidth | Attenuation | Differential voltage range | Common mode voltage range | Input impedance | Price |
|---|---|---|---|---|---|---|
| TA041 | 25 MHz | x10 / x100 | ±70 V / ±700 V | ±1400 V | 4 MΩ / 5.5 pF | In stock £195·00 US$321·75* €235,95* |
| TA057 | 25 MHz | x20 / x200 | ±140 V / ±1400 V | ±1400 V | 4 MΩ / 5.5 pF | In stock £220·00 US$363·00* €266,20* |
| TA058 | 50 MHz | x10 | ±70 V | ±700 V | 1.6 MΩ / 7 pF | In stock £245·00 US$404·25* €296,45* |
| TA044 | 70 MHz | x100 / x1000 | ±700 V / ±7000 V | ±7000 V | 10 MΩ / 10 pF | Low stock £480·00 US$792·00* €580,80* |
| TA043 | 100 MHz | x10 / x100 | ±70 V / ±700 V | ±700 V | 4 MΩ / 7 pF | In stock £450·00 US$742·50* €544,50* |
| TA042 | 100 MHz | x100 / x1000 | ±140 V / ±1400 V | ±1400 V | 4 MΩ / 7 pF | In stock £330·00 US$544·50* €399,30* |
| TA045 | 200 MHz | x10 | ±60 V | ±20 V | 500 kΩ / 7 pF | In stock £600·00 US$990·00* €726,00* |
BNC Attenuator Set
The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.
Please note: The TA050 attenuators must be used with a matched 50-ohm source and load. If you wish to attenuate a signal before feeding it into a high-impedance measuring instrument, you must add a 50 ohm feedthrough terminator such as the Pico Technology TA051 feedthrough terminator.
| TA050 Specifications | |
|---|---|
| Bandwidth | DC to 1 GHz |
| Attenuation | 3 dB, 6 dB, 10 dB, 20 dB |
| Maximum power dissipation | 1 W |
| Input impedance | 50 Ω |
| Output impedance | 50 Ω |
| VSWR | 1.5:1 or better |
| Dimensions | 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in) |
| Connectors | BNC, 1 male + 1 female |
| Construction | Shielded inner box with plastic shell |
| Weight | 24 g (approximately 0.85 oz) each |
| Lead time | In stock |
| Price | £39·00 US$64·35* €47,19* |
Feed-Through Terminator
The TA051 feedthrough attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50-ohm sources into instruments with high-impedance inputs, such as oscilloscopes.
| TA051 Specifications | |
|---|---|
| Bandwidth | DC to 1 GHz |
| Maximum power dissipation | 1 W |
| Input impedance | 50 Ω |
| Dimensions | 56 x 20 x 17 mm (approximately 2.2 x 0.8 x 0.7 in) |
| Connectors | BNC, 1 male + 1 female |
| Construction | Shielded inner box with plastic shell |
| Weight | 24 g (approximately 0.85 oz) each |
| Lead time | In stock |
| Price | £9·50 US$15·67* €11,49* |
PicoScope Carry Case
The PicoScope carry case can be used to protect your PicoScope Oscilloscope when used in the field, and to safely store it when it’s not needed.
The case uses foam to securely hold the PicoScope 2202, 3200 range and 4000# Series in place, preventing movement and providing cushioning to prevent damage. Space is also proved to store leads and scope probes.
Note: the PicoScope carry case is also supplied with our oscilloscope kits.
# Not suitable for use with the PicoScope 4262.
External dimensions: approximately 340 x 270 x 83 mm (13.4 x 10.6 x 3.3 in)
In stock
Price £30·00
(approx US$49·50 / €36,30)
* US Dollar and Euro prices are approximate. Your card will be billed in Pounds Sterling (GBP).
Share